Crafts · Geekery

That time I made Unicorn Headbands for a bunch of grown women…

What happens when a group of grown women get together to celebrate the upcoming nuptials of a magical friend?

We wear Unicorn Headbands!

wp-1485405923775.jpg

I recently volunteered to make Unicorn headbands for a magical themed bachelorette party. With the much appreciated help of a friend it wasn’t too difficult. By the end of the night we were Unicorn Headband making pros.

Supplies needed:

wp-1485394440803.jpg

  • Headbands (we used 1/4″ white plastic)
  • White felt (you can fit 2 horns onto one sheet)
  • Colored felt (we used 5 different colors, 1 sheet will get you 2, maybe 3 sets of ears)
  • Gold thread (we used embroidery floss, but recommend using something that won’t fray at the ends)
  • Glue Gun (and about 1 stick of glue per headband)
  • Tulle in assorted colors (6 – 3″x6″ strips for each headband)
  • Polyester fill/stuffing
  • Scissors

There are a few tutorials out there to make the horns using different methods. We ended up using the pattern from HowToGal’s Unicorn Headband tutorial and drew inspiration from a combination of headbands out there on the internets. You can improvise and make your own pattern, but having one premade sped things up (even though it took us a while to figure out exactly how to roll up those horns….)

The ear shape was drawn freehand and required one larger shape, and a smaller one to fit into the larger shape.

First step: Cut out the parts!

The white felt is used for the horn, the inner part of the ear (2 needed) and the base of the horn (2 needed).

wp-1485393608497.jpg

wp-1485394918413.jpg

The colored felt is used for the outer part of the ear….so you need two! To minimize the amount of cutting the pattern is meant to be cut on the fold! If you don’t do this, you won’t be able to attach it easily to the headband.

wp-1485395083744.jpg

wp-1485397064097.jpg
Be sure to cut on the fold so that both sides of the ear (front and back) are connected!!

Once you have all your parts cut out….

Step 2: The horn

This isn’t as complicated as I convinced myself it was…you basically apply a strip of glue to the edge of one side of the horn piece. Then you take the other edge, and rolling the piece, you place it over that glued edge.

20170125_211857.jpg

There’s probably a proper way to deal with the tip of the horn, but life is short, so most of them ended up with a little gap up top.

wp-1485397621165.jpg

Your horn is going to end up a little asymmetrical, so you just chop off that extra piece.

Step 3: Stuff and wrap! (Still working on the horn)

To properly stuff the horn you should use small pieces of fill to get to the very top of the horn. Then you gradually use larger pieces until the whole thing is firmly stuffed. Make sure to stuff the top well or your horn will droop later on.

To ensure that your horn does not look like a dunce cap, you can’t skip the gold thread! Start by tying the string as close to the top as you can. Then you bring the floss down in a spiral until you reach the bottom. The tighter you squeeze, the cuter it will look! Then you glue the end on the bottom, and tuck the loose end under.

Finally, apply glue to the bottom perimeter of the horn and attach to one of the circles. The circle is going to be bigger than the base of the horn so that you can trim it down once the glue has dried up.

Step 4: The Headband!

Now that you have a standalone horn, take the headband and find the center. Apply some glue (about 1-1/2″ wide), and stick that horn on! Then take the 2nd white circle, and glue that to the bottom so that the headband is sandwiched between the horn and the circle.

wp-1485397963654.jpg

Step 5: Ears!

Attaching the ears was my favorite part! Open up the “ear” piece, apply glue on the inside, and close it with the headband on the bottom edge. Make sure to leave room between the ear and the horn for the tulle!

Repeat that on the other side, and then glue on the inner ear.

wp-1485398031973.jpg

Step 6: Tulle!

The final step is adding the tulle strips! First you decide what order (yellow on the inside? blue  on the outside??), then you take one strip at a time and just tie it onto the headband!

wp-1485398102603.jpg

wp-1485398139306.jpg

….and you’re done!

wp-1485405809267.jpg

The headbands were a HUGE hit at the party, to the point that we wore them again to the Bridal Shower (and I wouldn’t be surprised if some make an appearance at the wedding next month as well).

I’ve been asked a few times whether I will be selling these. While they will not be listed in my Etsy shop, I will accept custom requests! Contact me for more information.

Advertisements

5 thoughts on “That time I made Unicorn Headbands for a bunch of grown women…

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s